GefonlineAuthorized Gefran Distributor
Sign InQuoteCart
Pressure Sensors · KE

KE Series NaK-Filled Melt Pressure Transmitters

NaK-filled melt pressure sensors with 4-20mA output, on-board autozero, and an optional stem-drift autocompensation function.

The KE series is Gefran's NaK-filled melt pressure transmitter line for plastics and rubber processing, built for process temperatures up to 538°C (1000°F). Where the mV/V-output K3 series requires an external amplifier or controller to interpret its signal, KE outputs a standard 4-20mA current loop directly, making it a drop-in fit for controllers that expect a transmitter rather than a raw sensor bridge.

Gefran KE Series NaK-Filled Melt Pressure Transmitters Melt - high temperature product photo

All F-Codes in This Family

Measurement PrincipleExtensimetric (strain gauge, bonded foil)
Supply Voltage10-30 Vdc
Isolation Resistance>1000 MOhm at 50 Vdc
Zero Balance4 mA (tolerance +/-0.25% FS)
Calibration Signal80% FS
Compensated Temperature Range0...+85 °C
Thermal Drift (Compensated Range)<0.02% FS/°C, combined zero/calibration/sensitivity drift (standard, non-autocompensated version)
Diaphragm Maximum Temperature538 °C (1000 °F)
Zero Drift vs. Process Temperature<3.5 bar/100°C (<28 psi/100°F), standard (non-autocompensated) version
Wetted Material — DiaphragmThree material options selected by the Contact Diaphragm order-code position: Inconel 718 with GTP+ coating (538 °C/1000 °F), 15-5 PH stainless with GTP+ coating (400 °C/750 °F), or Hastelloy C276 (300 °C/570 °F, not available for pressure ranges <=70 bar/1000 psi). 17-7 PH corrugated diaphragm with GTP+ coating used for ranges below 100 bar/1500 psi, rated 400 °C/750 °F.
Wetted Material — Stem17-4 PH stainless steel
Thermocouple OptionType J, isolated junction. Standard on model KE2 only.
Protection DegreeIP65, with 6-pole female mating connector fitted
Electrical Connector (6-Pin)VPT07RA10-6PT2 (mates with PT02A-10-6P)
Electrical Connector (8-Pin)PC02E-12-8P (Bendix)
Pressure Range0-35 to 0-1000 bar (0-500 to 0-15000 psi) across the full order-code range table
Maximum Overpressure2x full scale; 1.5x full scale above 700 bar / 10000 psi
Accuracy Class H+/-0.25% FS, available on ranges >= 100 bar / 1500 psi
Accuracy Class M+/-0.5% FS, available across the full range table (35-1000 bar / 500-15000 psi)
Installation Max Torque56 Nm (500 in-lb) maximum tightening torque
Autocompensation FunctionThe Autocompensation (SP) version cancels the effect of pressure-signal variation caused by melt-temperature variation, via internal self-compensation, reducing read error from filling-fluid heating (a known limitation of 'filled' sensor technology in general). Available only for ranges >100 bar; not available for the KE3 (exposed capillary) version.
Autozero FunctionSignal variations in the absence of pressure can be eliminated with the Autozero function, activated by closing a magnetic contact on the transmitter housing. Permitted only with pressure at zero. Available as on-board (magnetic) or external option — see autozero_type order-code position for which one a given part has.
Electronic Response Time~1 ms (10-90% FS)
Fill FluidNaK (sodium-potassium), a near-incompressible hydraulic transmission fluid classed as Generally Recognized as Safe (GRAS) and compliant with the Restriction of Hazardous Substances (RoHS) Directive.
Fill Fluid VolumeKE0: 30 mm3 [0.00183 in3]. KE1, KE2, KE3: 40 mm3 [0.00244 in3].
Max Current Absorption32 mA
Operating Temperature Range-30...+105 °C
Output Noise<0.025% FS (RMS, 10-400Hz)
Output Signal Type4-20mA, 2-wire loop
Short Circuit Reverse Polarity ProtectionYes
Storage Temperature Range-40...+125 °C
Zero Drift Autocompensated VersionAutocompensation (SP) version, over a 20-500 °C media-temperature range: <0.005 bar/°C for 100 ≤ p < 500 bar; 0.0022% FS/°C for p ≥ 500 bar. These drift values are valid only up to 500 °C media temperature.

Need engineering support?

Our technical team can help you specify the right KE configuration for your application.

Contact Support

You might also need