GefonlineAuthorized Gefran Distributor
Sign InQuoteCart
Pressure Sensors · K3

K3 Series NaK-Filled Melt Pressure Transducers

Sodium-potassium-filled melt pressure sensors rated to 538°C, for the hottest engineered-polymer processing lines.

The K3 series is Gefran's highest-temperature melt pressure transducer line for plastics and rubber processing, built for process media that can reach 538°C (1000°F) — well above what the mercury-filled M3 series is rated for. Rather than exposing a strain gauge directly to that heat, the K3 design carries the pressure signal hydraulically through a sodium-potassium (NaK) fill to a bonded foil strain gauge positioned away from the hottest zone, which is what lets the diaphragm withstand extreme process temperatures while the sensing electronics run in a much more moderate range.

Gefran K3 Series NaK-Filled Melt Pressure Transducers Melt - high temperature product photo

All F-Codes in This Family

Measurement PrincipleStrain gauge (bonded foil strain gage technology)
Supply Voltage6-12 Vdc (10 Vdc typical)
Bridge Resistance350 Ohm standard; 550 Ohm below 100 bar / 1500 psi
Isolation Resistance>1000 MOhm at 50 Vdc
Output (FSO)2.5 mV/V (order code 2); 3.33 mV/V (order code 3), tolerance +/-0.5% FSO
Zero Balance+/-5%
Calibration Signal80% FSO
Compensated Temperature Range0...+100 °C (32...212 °F)
Maximum Temperature Range-30...+120 °C (-22...250 °F)
Thermal Drift (Compensated Range)<0.02% FSO/°C (<0.01% FSO/°F), combined zero/calibration/sensitivity drift
Diaphragm Maximum Temperature538 °C (1000 °F)
Zero Drift vs. Process Temperature<3.5 bar/100°C (<28 psi/100°F)
Wetted Material — DiaphragmThree material options selected by the Contact Diaphragm order-code position: Inconel 718 with GTP+ coating (rated to 538 °C/1000 °F), 15-5 PH stainless with GTP+ coating (rated to 400 °C/750 °F), or Hastelloy C276 (rated to 300 °C/570 °F, not available for pressure ranges <=700 bar/10000 psi). A 17-7 PH corrugated diaphragm with GTP+ coating is used for ranges below 100 bar/1500 psi, rated to 400 °C/750 °F.
Wetted Material — Stem17-4 PH stainless steel
Thermocouple OptionType J, isolated junction. Standard on model K32 only.
Protection DegreeIP65, with 6-pole female mating connector fitted
Electrical Connector (6-Pin)VPT07RA10-6PT (mates with PT02A-10-6P)
Electrical Connector (8-Pin)PC02E-12-8P
Pressure Range0-35 to 0-1000 bar (0-500 to 0-15000 psi) across the full order-code range table
Maximum Overpressure2x full scale; 1.5x full scale above 700 bar / 10000 psi
Accuracy Class H+/-0.25% FSO, available on ranges >= 100 bar / 1500 psi
Accuracy Class M+/-0.5% FSO, available across the full range table (35-1000 bar / 500-15000 psi)
Installation Max Torque56 Nm (500 in-lb) maximum tightening torque
RoHS Scope RestrictionManufactured in compliance with the Electromagnetic Compatibility (EMC) Directive and Restriction of Hazardous Substances (RoHS) Directive.
Fill FluidNaK (sodium-potassium), a near-incompressible liquid used for hydraulic pressure transmission; classed as Generally Recognized as Safe (GRAS) and compliant with the Restriction of Hazardous Substances (RoHS) Directive.
Fill Fluid VolumeK30: 30 mm3 [0.00183 in3]. K31, K32, K33: 40 mm3 [0.00244 in3].

Need engineering support?

Our technical team can help you specify the right K3 configuration for your application.

Contact Support

You might also need